I don't know how to set it. I have like 60 horizontal and 60 vertical sharpness right now, and either no edge enhancer or it's set on low. I feel like the edges are a little jagged and also not as sharp and smooth as I want.
I've seen some calibrations for other LG tvs with very low sharpness...
Yesterday my iPhone automatically changed an hour back for DST, this morning it had changed back so is now an hour off.
All of the settings are correct but my phone says it's an hour later than it actually is.
In the settings it says time is auto, how can I manually correct the time?
Im noticing that when the bike turns on, the idle goes way up (high enough that i feel like shifting gears) even though its idling. I cant seem to find a decent picture anywhere of how to adjust the idle.. And another problem is, most of the screws are so soft that when i try to turn them, the...
I have a 99 Arctic cat zl 600. I would like to adjust the rear suspension in order to support more weight, I do not have a manual I assume it would be fairly easy and only require a wrench, correct? I am not vary snowmobile savvy. Also what do you think would be the weight limit on my sled,or...
V Brakes..
It seems like I am adjusting my brakes a lot after tire repairs on the trail. when replacing the wheel, I have to adjust my cable fixing bolt so the ve brakes grab properly, and also let the tire spin. is it normal to have to do this every time I fix a flat?
I have 2 kicker 08 l5's rated at 450 watts rms a piece and a kicker 750.1 rated at a true power rating of 942 watts is it ok to run 900 watts into the subs and what should i adjust the bass bosst on my amp for maximum efficiency
Everything i can find on the net says there's a screw on the light that you turn to adjust it, but i can't find any screw.
It's a 2000 Opel Corsa if that helps
I can not figure out where are the headlight adjusting screws both vertical and horizontal aim on a 1992 Lexus LS 400. My driver side headlight is a little to high up and I need to adjust it. Please help. If you have pics showing the location that would be helpful or a detailed explanation of...
I can not figure out where are the headlight adjusting screws both vertical and horizontal aim on a 1992 Lexus LS 400. My driver side headlight is a little to high up and I need to adjust it. Please help. If you have pics showing the location that would be helpful or a detailed explanation of...
I noticed that the colors where a little out of sync on my older R/P TV. I never knew about convergence and found the option to manually adjust it in the menus. It gives me a large grid that allows me to move and adjust red and blue lines. Is it bad for my TV if I moved many of these lines to...
Im trying to adjust all the stuff on my tv, when I go to menu it keeps telling me "not available in current mode" I want to adjust the picture, color etc.
I just picked up a new 42' ProScan HDTV and I can't figure out how to adjust the settings from 420i up to 1080p...Unfortunately, this was an 'open box' purchase and the retailer didn't have the directions..nor can I find a copy online. Aren't HDTV's suppose to allow you to adjust settings from...
I have a 91 Chevy 2500 that I recently done work on the timing. I placed a roller cam from a 99 5.7 Vortec. I'm almost sure that I have it timed correctly, but the valves seem to not open all the way. I still need the rockers adjusted. Does anyone know how to do this step correctly?
Is there a way to adjust the clutch? It has just started to slip (under high revs in the lower gears) There is no play in the pedal i.e. it disengages about an inch in. I know the clutch will have to be replaced eventually but it has only done 60,000 miles and would like to delay the inevitable...
Hello,
I would like to know whether to change my 6 meal(breakfast, snack #1, lunch, snack #2, dinner, snack#3) plan from regular time of 8AM- 10PM to 3 PM- 6AM? The reason being is that I am now in a graveyard type of schedule, so any inputs out there is greatly appreciated.
I adjusted the valves on my 350 and then when I went back to TDC The valves on the number 1 cylinder were loose. Is this ok? Is it becasue it has hydralic lifters and they leak down?
I just replaced my old yellowed headlights on my Jeep Grand Cherokee, but can find no info on adjusting the lights, not even in my book. I need to know which adjusting screws are used to lower the lights. Thanks.